#Okidata c5800 gear slipping software#
#Okidata c5800 gear slipping windows#

At first change the stapler unit, and if it becomes the error again, change the cable. An error was detected in expanding image data.Ĭommunication Error with Operator Panel UnitĬheck the stapler unit and cable. Record the figures on the lower right side of the LCD, and cycle the power. If display the address on the LCD, record the figures and close the error display and cycle the power.ĭetection of abnormal condition of the PostScript firmwareĭetection of abnormal condition during image data expansion Malfunction of the NIC chip was detected. If power cycling does not solve the problem maintenance by a service engineer is required Power off the MFP and attach the hard disk and power on the MFP.ĭetect the time out between the Controller unit and scanner unit 01 : No ACK for read beginning command 02 : No ACK for read cancel command 03 : No ACK for SIP cancel commandĭetect the error at scanner control section 01 : SIP internal error 02 : Scan Model internal error 03 : SPB internal errorĭetect the communication error with the Sleep Mode interface supervisor program.Ī communication error was detected during communication with the Sleep Mode interface monitoring program. Check the connection between the scanner and printer.Ĭontroller unit cannot detect the hard disk Push the button and close the error screen, after a record with all numerical value displayed on LCD. You can almost see the smile at the other end of the line.

The telephone is answered promptly and efficiently.

Record the figures on the LCD, and close the error display.Ĭontroller unit cannot detect the scanner unit My dealings with the staff at Ok Oki has found them to be always friendly, helpful and kind. 054:Error xxx yyy zzzĭetect the communication error between the Controller unit and scanner unit The NIC-F/W must be written with the maintenance utility after formatting.) If the error remains replace the printer control PCBĪbnormal condition of the CPU cooling fan on the CU PCBĭoes it recover from the error by replacing the fan?ĭMA Abort Error was detected with Image Processor (This requires caution as it erases NIC-F/W. Replace the CU/ PU board.įailed to access to the Flash ROM that is mounted directly on the CU PCBįormat the Flash forcibly. Re-implement the RAM DIMM and turn on the MFP. The CU FW in Nand FLASH has not been detected or a check SUM error has occurredĬU Program detects the error for hash on the DIMM slotĬycle the power. Pehuea Womens Slip On Sneakers, Casual Everyday Shoes with Drop-in Heel & Breathable Mesh Design, Lightweight & All-Day Comfort 4.6 out of 5 stars 1,393 100.00 100. Push the button and close the error screen, after a record with all numerical value displayed on LCD.Ī watchdog timeout occurred due to no system timer interrupt for unknown reasons Replace the CU/PU board.Įxception hardware problem was detected (PCB failure or insufficient power capacity)

#Okidata c5800 gear slipping windows#

Testing for other printers on Windows XP (although other OSs may work).Machine Check Exception hardware fault detection (board failure or poor power supply)Ĭycle the power. Reported to work on WGP606, but not tested Reported to work on WGPS606 but not tested Test page not supported, except on WGPS606 Looking for PS121v2 (not v1) compatibility list? See NETGEAR PS121v2 - Print server compatibility list Company Turn the two fasteners (a) 90° to the right until they lock.

#Okidata c5800 gear slipping software#

Generally this is due to non-standard software such as CAPT and GDI. Locate the drive gear into the gear inside the printer by the rear left corner of the unit, and lower the belt unit flat inside the printer.

A few printers are incompatible with most print servers, including NETGEAR's.

E.g., search '660', instead of 'Epson Stylus Color 660'.

You can use a browser or the Support search to look just for a printer number.

Other printers and features may be compatible, but NETGEAR has not tested them.

Except as noted, bidirectional features, such as reporting ink status to networked computers, are not supported.

(This is true of all non-NETGEAR products, too.)

Multifunction printers such as combination printer/copier/fax only support the printing function.

The new WGPS606 print server, however, supports other printers.

Supported printers either use USB or parallel printing.

This lists the printers compatible with NETGEAR print servers.